SW80P Single Pole Single Throw Normally Open - IP660 pages
- IP66
100A/125ASW80P Single Pole Single Throw Normally OpenSeries)
(Part of the SW80
Application
Interrupted
Uninterrupted
100A
125A
30% Duty
185A
230A
40% Duty
160A
200A
50% Duty
140A
175A
60% Duty
130A
160A
70% Duty
120A
150A
The SW80P is sealed to IP66 and has been designed for direct current
loads in more ardous environments. Applications include winches
and motors as used on electric vehicles such as industrial trucks.
Developed for both interrupted and uninterrupted loads, the SW80P
is suitable for switching Resistive, Capacitive and Inductive loads.
Thermal Current Rating (Ith)
Intermittent Current Rating:
•t
•t
800A at 48V
Rated Fault Current Breaking Capacity (Icn) Resistive Load:
(in accordance with UL508*)
SW80P
Uninterrupted current - no or infrequent load switching requirements
(maintains a lower contact resistance).
The SW80P features single pole double breaking main contacts with silver
alloy tips, which are weld resistant, hard wearing and have excellent
conductivity. The SW80P features an enclosed top cover and offers
environmental protection to IP66. The SW80P has M8 stud main
terminals and 6.3mm spade coil connections. Mounted using supplied
brackets, mounting can be horizontal or vertical, when vertical the M8
contact studs should point upwards. If the requirement is for downwards
orientation we can adjust the contactor to compensate for this.
Rated Fault Current Breaking Capacity (Icn) 5ms Time Constant:
(in accordance with UL583*)
SW80P
Interrupted current - opening and closing on load with frequent
switching (results in increased contact resistance).
190A at 60V D.C.
SW80P
Maximum Recommended Contact Voltages (Ue):
SW80P
48V D.C.
Typical Voltage Drop per pole
across New Contacts at 100A
60V D.C.
40mV
Mechanical M.T.B.F
>5 x 106
Coil Voltage Available (Us)
(Rectifier board required for A.C.)
From 6 to 240V D.C.
Coil Power Dissipation:
Highly Intermittent Rated Types
20 - 30 Watts
Intermittently Rated types
15 - 20 Watts
Prolonged Rated Types
13 - 15 Watts
Continuously Rated Types
7 - 13 Watts
Maximum Pull-In Voltage (Coil at 20˚ C) Guideline:
Highly Intermittent Rated types
(Max 25% Duty Cycle)
60% Us
Intermittently Rated types
(Max 70% Duty Cycle)
60% Us
Prolonged Operation
(Max 90% Duty Cycle)
60% Us
Continuously Rated Types
(100% Duty Cycle)
66% Us
10 - 25% Us
Typical Pull-In Time
800
5ms
50ms
Key:
●
Magnetic Latching† (Not fail safe)
Closed Contact Housing
Environmentally Protected IP66
○
●
●
EE Type (Steel Shroud)
X
80mm2 [0.124inch2]
Contact Performance Key:
Interrupted Current
Uninterrupted Current
= Uninterrupted
* Please check our web site for product UL status
•t
•t
•t
v1a-06-13
Performance data provided should be used as a guide only. Some de-rating or variation
from figures may be necessary according to application.
Thermal current ratings stated are dependant upon the size of conductor being used
For further technical advice email: technical@albrightinternational.com
Albright reserve the right to change data without prior notice
Connection Diagram
0
80
70
0
60
0
50
0
0
Current (Amperes)
Note: Where applicable values shown are at 20˚C
•t
40
0
30
0
Rated suitable for Application
= Interrupted
X
Mounting Brackets
(See Stud Range Catalogue)
0
Advised Connection Sizes for Maximum Continuous Current
Cable
X
300
400
0
Guideline Contactor Weight:
390 gms
X
Armature Cap
20
- 40˚C to + 60˚C
Copper busbar
500
X
Magnetic Blowouts†
Magnetic Blowouts - High Powered†
600
100
3ms
Operating Ambient Temperature
Auxiliary Contacts - V3
Figures are for guideline
purposes only
700
X
200
8 - 20ms
Typical Contact Bounce Period
Suffix
Auxiliary Contacts
0
With Diode Suppression
Time (Seconds)
Without Suppression
SW80P
General
900
Typical Drop-Out Time (N/O Contacts to Open):
With Diode and Resistor
(Subject to resistance value)
SW80P Available Options
SW80P Contactor Performance
20ms
10
Drop-Out Voltage Range
Dimensions in mm [inches]
M
P
Contacts
○
○
Large Tips
Textured Tips
Silver Plating
L
T
X
Coil
AC Rectifier Board (Fitted)
X
Coil Suppression†
○
Flying Leads
X
Manual Override Operation
X
M4 Stud Terminals
○
M5 Terminal Board
X
Vacuum Impregnation
○
Key: Optional
†
○
Standard
●
Not Available X
Connections become polarity sensitive
Albright International Ltd, Evingar Trading Estate, Ardglen Road, Whitchurch, Hampshire, RG28 +44 UK
Albright International, 125 Red Lion Road, Surbiton, Surrey KT6 7QS, England,Tel: +44 (0) 20 8390 5357, Fax:7BB,(0) 20 8390 1927
Tel: sales@albrightinternational.com or technical@albrightinternational.com Web 890030, Fax: +44 (0)1256 890043
E-mail: +44 (0)1256 893060, Fax: +44 (0)1256 893562, Dedicated Sales Tel: +44 (0)1256 Site: www.albrightinternational.com
E-mail: sales@albrightinternational.com or technical@albrightinternational.com Web Site: www.albrightinternational.com
Copyright © 2010 Albright International Ltd
Copyright © 2013 Albright International LTD
SW80P
"