PVPC pumps0 pages
www.atos.com
Table A170-7/E
Proportional electrohydraulic controls for PVPC pumps
pressure-flow alternate P/Q controls, analog or digital
The variable displacement axial piston
pumps type PVPC, can be supplied with
advanced electrohydraulic proportional
controls:
• open loop pressure control;
• load sensing flow control;
• Open and closed loop P/Q controls;
They allow to perform high dynamics and
fine regulations, directly commanded from
PLC or from the machine controller. They
are available with separated driver or with
integral electronics ቢ.
New PES digital controllers, integrated to
the pump, realize alternate closed loop
controls of pressure, flow and max power
limitation. The P/Q controls are also available
with optional sequence module (LZQZR or
PERS versions) that allow to operate the
pump with minimum pressure in the circuit
close to zero. Following communication
interfaces are available for the digital PE(R)S
execution, see section :ݟ
• -PS: Serial
• -BC: CANopen
• -BP: PROFIBUS DP
For technical characteristics and features of
the PVPC pumps, see table A160.
PVPC-PES-PS-4046
1
MODEL CODE
PVPC
X2E -
PERS
- BC -
4
046
/31044 /
*
/1
D / *
10
Additional suffix for double pumps
X2E = with a fixed displacement
pump type PFE (see tab. A005)
Series number
Type of control (see section ݝand :)ݞ
CZ
= proportional pressure compensator
LQZ
= proportional flow control (load sensing)
LZQZ = proportional pressure & flow control (load sensing)
LZQZR = as LZQZ plus sequence module
PES
= closed loop integral digital P/Q controller
PERS = as PES plus sequence module
Options, for CZ, LQZ, LZQZ, LZQZR
see sections :ݙ
18 = optional coil for low current drivers
Electronics options for PES and PE(R)S
see sections ݚand :ݝ
I = current reference input and monitor
output signals (4 ÷ 20 mA)
C =current feedback input signal (4÷20 mA)
for remote pressure transducer
X =with integral pressure transducer (only
for PERS)
S =with two on-off inputs for multiple
pressure PID selection (PS execution)
or double power supply (BC and BP
execution)
Communication interface, only for PES and PERS versions
PS = Serial BP = PROFIBUS DP BC = CANopen
Size:
3 = for displacement 029 4 = for displacement 046 5 = for displacement 073 and 090
Max displacement:
029 = 29 cm3/rev
046 = 46 cm3/rev
/*
Seals material:
omit for NBR (mineral oil &
water glycol)
PE = FPM
See notes in section ݘ
Variable displacement
axial piston pump
073 = 73 cm3/rev
Direction of rotation (viewed at the shaft end)
D = clockwise
S = counterclockwise
090 = 88 cm3/rev
Type of PFE (for double pumps), see tab. A005
Pressure setting (only for PERS): 200 = 200 bar
250 = 250 bar
Shaft (SAE Standard):
1 = keyed (7/8” for 029 - 1” for 046 - 1 1/4” for 073 and 090)
5 = splined (13 teeth for 029 - 15 for 046 - 14 for 073 and 090)
280 = 280 bar
1) pumps with ISO 3019/2 mounting flange and shaft (option /M) are available on request
2
OPERATING CHARACTERISTICS
Pump model
Displacement
PVPC-*-3029 PVPC-*-4046 PVPC-*-5073 PVPC-*-5090
[cm3/rev]
29
46
73
88
[l/min]
42
66,7
105,8
127,6
Max working pressure / Peak pressure [bar]
280/350
280/350
280/350
250/315
Min/Max inlet pressure
[bar abs.]
0,8 / 25
0,8 / 25
0,8 / 25
0,8 / 25
Max pressure on drain port
[bar abs.]
1,5
1,5
1,5
1,5
Power consumption at 1450 rpm and at [kW]
maximum pressure and displacement
19,9
31,6
50,1
54,1
External load position
Theorical max flow at 1450 rpm
Max torque on the first shaft
Max permissible load
on drive shaft
Speed rating
[Nm]
Fax
[N]
Frad
Type 1 Type 5 Type 1 Type 5 Type 1 Type 5 Type 1 Type 5
200
190
230
330
490
620
490
620
1000
1500
2000
2000
1500
1500
3000
3000
[rpm] 600 ÷ 3000 600 ÷ 2600 600 ÷ 2200 600 ÷ 1850
Fax = axial load
Frad = radial load
Notes: For speeds over 1800 rpm the inlet port must be
under oil level with adequate pipes.
Maximum pressure for all models with water glycol fluid is
160 bar, with option /PE is 190 bar.
Max speed with options /PE and water glycol fluid is
2000/1900/1600/1500 rpm respectively for the four sizes.
A170