"

PSEi

nnnn

Plastic Belt Conveyor

nnnn

The Model PSB with modular plastic belting uses a

nnnn

positive drive system to eliminate belt slippage and

nnnn

mistracking.

nnnn

16 Belt Widths

nnnn

Polypropylene 2" Pitch Plastic Belt

nnnn

Adjustable MS-Type Floor Supports Available

nnnn

Conveyor shown with

nnnn

optional floor supports

nnnn

-<

nnnn

O

nnnn

I—

nnnn

n

nnnn

o

nnnn

-<

nnnn

o

nnnn

70

nnnn

n

nnnn

o

nnnn

SIZE TO ORDER Overall Length

Belt Width

8"

10"

12"

14"

16"

18"

20"

22"

24"

26"

28"

30"

32"

34"

36"

38"

Between Rail Width Overall Frame Width

9"

11"

13"

15"

17"

19"

21"

23"

25"

27"

29"

31"

33"

35"

37"

39"

12"

14"

16"

18"

20"

22"

24"

26"

28"

30"

32"

34"

36"

38"

40"

42"

10'

Weights

328

248

368

388

408

428

448

468

488

508

528

548

568

588

608

628

Weights Per Foot

18

20

22

24

26

28

30

32

34

36

38

40

42

44

46

48

nnnn

LOAD CAPACITY CHART @ 65 FPM
HP	16"T0 28" OVERALL WIDTH
	TOTAL LOAD (LBS.)
	UP TO 50'
y-i	750
i	1750
2	3750

nnnn

OVERALL LENGTH"A"

nnnn

7-3/4" 7-1/2" (

nnnn

-20 TOOTH, 6.4" PITCH DIA. PLASTIC SPROCKETS

nnnn

JOTALLY ENCLOSED

nnnn

CHAIN GUARD

nnnn

PLASTIC BELT-

nnnn

OVERALL FRAME WIDTH

nnnn

- BETWEEN RAIL WIDTH -

nnnn

• STANDARD SPECIFICATIONS

nnnn

END DRIVE-Located on discharge end of conveyor. Chain guard located on left hand side.

nnnn

BELT—Polypropylene 2 in. pitch Flush Grid, nominal 1 in. less than BR.

nnnn

BED-UHMW on aluminum slider bars, mounted to frame spacers. Mounted in 7 % in. x 12 ga.

nnnn

powder painted, formed steel channel frame bolted together with butt couplings.

nnnn

CROSS BRACING-Rods with turnbuckles are fastened to underside of bed to provide alignment of

nnnn

bed sections to insure correct belt tracking. Supplied on every other section 30 ft. bed lengths and

nnnn

over.

nnnn

DRIVE AND TAIL SPROCKETS-10 tooth 6.4 in. pitch dia. molded plastic sprockets on 1 % in. sg.

nnnn

shaft, 13/i6 in. dia. shaft at bearings.

nnnn

OPTIONAL EQUIPMENT

nnnn

FLOOR SUPPORTS-MS Type floor supports are available with a wide range of adjustment. Specify

nnnn

top of belt or roller elevation. One support reguired at every bed joint and ends of conveyor. Holes

nnnn

in feet for lagging to floor. Knee braces recommended above MS-6 support.

nnnn

BED-Stainless steel in lieu of powder painted HRS (Excluding Aluminum Support Bars).

nnnn

BELT-Other belts available, contact factory.

nnnn

BELT SPEED-Other constant and variable speeds. V-belt drive supplied on speeds under 15 FPM

nnnn

and with variable speeds. Note: Capacity affected with speed change.

nnnn

V-BELT DRIVE—V-belt supplied between motor and reducer. Allow 65 in.

nnnn

TOTAI I Y

nnnn

FRAME SPACER ^—UHMW WEARSTRIPS ENCLOSED

nnnn

CHAIN

nnnn

GUARD

nnnn

SECTION X-X

nnnn

SNUB ROLLERS-Located at drive and tail ends.

nnnn

RETURN BARS-UHMW on aluminum.

nnnn

BEARINGS-Sealed, pre-lubricated, self-aligning ball bearings on drive and tail shafts.

nnnn

SPEED REDUCTION-Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive sprocket.

nnnn

MOTOR-tt HP-208/230/460/575V-3 Ph. 60 Hz. Totally Enclosed C-Face.

nnnn

BELT SPEED-Constant 65 FPM.

nnnn

CAPACITY-Maximum load per linearfoot of conveyor 200 lbs. NOTTO EXCEED capacity in chart.

nnnn

O-RING DRIVE CHAIN-With sealed in lubricant (Recommended for applications that do not permit

nnnn

regular lubrication).

nnnn

CEILING HANGARS-% in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and

nnnn

galvanized rods available.

nnnn

NOSEOVER AND NOSEUNDER-Can be incorporated to provide continuous belt travel from

nnnn

horizontal to incline or decline.

nnnn

MOTORS-Energy efficient, single phase, brakemotor, other haracteristics. 2 HP maximum.

nnnn

ELECTRICAL CONTROLS-One direction magnetic starters and push-button stations. AC Variable

nnnn

Freguency Drive.

nnnn

HYTROL CONVEYOR CATALOG

nnnn

02012013

"