Light Duty Portable Parts Conveyor
•t
•t
•t
•t
•t
6 Belt Widths
Reversible
Overhead Drive
One Piece Troughed Bed
Adjustable PCAS Type Floor Supports Available
OVERALL LENGTH "A"
2-1/8" DIA.
TAIL PULLEY
2"
3-1/4"
12"
12 1/2"
17 1/8"
134
146
158
181
205
18"
18 1/2"
23 1/8"
162
178
196
228
262
I N C.
4"
6"
8"
10"
4 1/2"
6 1/2"
8 1/2"
10 1/2"
9 1/8"
11 1/8"
13 1/8"
15 1/8"
96
107
116
125
100
114
124
128
Weights
106
121
133
145
(Lbs.)
116
139
150
165
126
146
166
186
All weights in catalog are conveyor weights only. Accessories, crating, etc., are not included.
CO M P A N Y ,
Belt Width
Bed Width
"B"
CO N V E Y O R
The Model “PCA” Conveyor is easily positioned in
or under punch presses, plastic injection molding
machines, extruding equipment, and other machinery,
where small steel or aluminum stampings, plastic parts,
etc., must be quickly conveyed to hoppers or drums to
keep production on the move.
SIZE TO ORDER
Overall
Length "A"
4'
5'
6'
8'
10'
HY TR O L
PCA
"B"
16"
19-45/64"
6-3/8"
MIN.
1-3/8" DIA. RETURN IDLER
11-3/8"
6-1/2"
• Standard Specifications
OVERHEAD END DRIVE–Located on discharge end of conveyor. Chain guard located on left hand
side.
BELT–Black Ultimate 140 SD. Clipper lacing.
BED–12 ga. steel formed troughed bed section with 1 in. high vertical sides.
DRIVE PULLEY–2 1/2 in. dia. with 1 in. dia. shaft, crowned and fully lagged.
TAIL PULLEY–2 1/8 in. dia. with 7/16 in. dia. threaded shaft. Pre-lubricated ball bearings.
RETURN IDLER–Adjustable 1 3/8 in. dia. pre-lubricated ball bearings.
BED WIDTH
2-1/2" DIA.
DRIVE PULLEY
BELT WIDTH
TAKE-UP–Screw take-ups are provided at drive pulley to insure proper belt tension.
BEARINGS–Sealed, pre-lubricated ball bearings on drive pulley.
SPEED REDUCTION–Sealed worm gear “C” face speed reducer. No. 40 roller chain to drive pulley.
MOTOR– 1/2 HP–230/460V–3 Ph. 60 Hz. Totally Enclosed Fan Cooled “C” face.
BELT SPEED–Constant 65 FPM.
CAPACITY–Maximum load per linear foot of conveyor 10 lbs.
• Optional Equipment
FLOOR SUPPORTS–PCAS Type floor supports are available with a wide range of adjustment. Specify
top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in
feet for lagging to floor. Knee braces recommended above PCAS-6 support.
BED–Higher than 1 in. high vertical sides.
BELT–White Polymate 100 RPM COS.
MOTORS–Energy efficient, single phase, other characteristics. 1/2 HP maximum.
BELT SPEED–Other constant speeds 11 to 82 FPM, specify.
ELECTRICAL CONTROLS–Manual one direction push button switch, one direction magnetic starters,
push button stations, power cord.
Hytrol Conveyor Catalog
02012013
UNDERSIDE DRIVE–Gearhead motor mounted underneath bed section.
12.9