Rubbol WP 1930 pages
application by brush for windo'
equipment with
limited dimension stir before u
stable wooden
constructions
water thinnable
sikkens
WOOD COATINGS
Rubbol WP 193
Product description
Colour
Binder type
Pigments
Packaging
Processing
Consumption
Thinning
Application temperature
Drying times
Waterborne, white sprayable base and mid coat for constructions made of soft and hard wood with isolating properties
against discolouring inhabitors from hard woods, exterior and interior.
- good pore wetting
- high filling properties
- neutral odour
- good sanding properties
White
Acrylic -Alkyd resin combination
Titanium dioxid
20 L, 120 L
Brushing, only for semi.stable wooden constructions
Spraying
Wet film thickness: 1 X 100 to 150um
100 - 150 ml/m2 depending on applied wet film thickness per coat without losses.
60 - 80 ml/m2 with a brush application depending on the type and absorbtion properties of the timber (exact values
must be determined in trails).
If necessary with water max. 5 %.
15 - 25 °C for substrate, air and material at approx. 60 % R.H.
The drying process of the coating depends on the applied wet film thickness and can extend when using timber with a
high extract contents or drying in damp/cold conditions. During the drying process one should ensure for adequate
temperature and ventilation.
If the drying conditions are not upheld, damages within the coating cannot be warranted.
To achieve optimal isolating properties, a curing time of minimal 8 hours is required!
Drying at 23 °C / 50 % R.H.
Dust dry: after approx. 30 minutes
Sandable: after approx. 4 - 6 hours
Recoatable: after approx. 8 - 10 hours waterborne
Clean directly after use with water, if needed with washing up liquid or with ST 830.
The minimum storage stability of sealed containers is 2 years.
Storage temperature: +5 - +30 °C.
After ending of the storage time the product still can be usable, but some attributes may vary from new product.
Therefore such over-stored product has to be applied with special attention.
Opened cans must be sealed correctly! Store in a cool but frost-protected area.
Only residue emptied cans can be disposed via recycling. Liquid wastes must be disposed of according to national
regulations or according to EU-disposal key 08 01 12.
In accordance with EC guide lines - Material safety data sheet, point 15.
Before use, read the identification and product information. Even when working with low emission products one should
take care of the customary protection measures.
The wood moisture content for the application of Sikkens coating systems should be between 12 % and 15 %.
According to the guidelines for window coating systems, published by the Federal German Committee for Paint and
Material Value Protection (Instruction Leaflet No. 18), of VOB, Parte, DIN 18363, and the recommendations of the
German Institute for Window Technology e.V. in Rosenheim, all wooden constructions in buildings must be coated on all
sides with at least one primer and one intermediate coat (minimum dry film thickness 30 urn) before they are
incorporated in buildings. The choice and use of the coating system, especially the colour shade, should also be taken
into account. Darker shades can increase the surface temperature (up to 80 C).
For use in a technical industrial companies and exclusively released for Sikkens systems recomondations.
To ensure a correct adhesion of the following coating system, the paint system should not be sanded down to the
substate.
With some wood species, especially hardwoods, discolouration can appear due to natural wood extractives.
VOC guideline EU limit value for this product (Kat. A/d): 50 g/l (2007)/30 g/l (2010). This product contains max. 30 g/l VOC.
Relevant information The here mentioned coating system is only an example, other systems are possible.
All external materials (i.e. fillers, tapes, sealing compounds, cleaners) must be checked for compatibility with the coating
system before use.
Please observe the relevant Technical Data Sheets or seek advice from the Sikkens sales representative or contact the
technical centre.
When using Rubbol WP 193 on larch, cracking can occure in isolated cases.
Cleaning of equipment
Storage
Disposal
Hazard identification
Warning
General instructions
Akzo Nobel Industrial Coatings Ltd Unit 4a, Mercer Way, Shadsworth Blackburn, Lanes, BB12QZ
Bus Pk
Akzo Nobel Industrial Coatings Ltd Unit 4a, Mercer Way, Shadsworth Blackburn, Lanes, BB12QZ
Bus Pk
Akzo Nobel Wood Coatings GmbH Diisseldorfer StraGe 96-100 40721 Hilden
AkzoNobel
United Kingdom Tel. +44 1254 687950 Fax. +44 1254 687960
Rep of Ireland Tel. +35 (0) 21 4220222 Fax. +35 (0) 21 4220205
Germany Tel.: +49-2103-77-800 Fax: +49-2103-77-577
"