Cetol WF 732 OilFinish0 pages
■n
limited dimension stir before u
stable wooden
constructions
/ater thinnable
sikkens
WOOD COATINGS
cleaning of
equipment with
Cetol WF 732 OilFinish
Product description Waterborne, translucent, deep matt wood oil as mid and finish coat for exterior and interior wooden constructions. Low
or medium build translucent natural effect varnish that emphasizes the wood structure.
- moisture permeability
- wood moisture regulating
- good leveling
- easy to apply
Colour With the choice of the different translucent colours, one should observe the Rosenheimer paint classification table. All
translucent colours can be mixed with each other. The optical appearence of different systems can differ depending on
substrate and wet film thicknesses, for this reason one should make trials before application.
Dark translucent colours give better weather durability than light colours. Colourless systems are not suitable for
exterior.
Timbers which contain extractives i.e. Oak, Larch or tropical woods can cause discolouring - these can appear after
weathering.
Translucent, colour tints i.e. from the Joinery Colour Collection.
Gloss level Deep matt
Binder type Acrylat with add on of natural oils
Packaging 20 L
Processing Spraying
Wet film thickness: 2 X 80-120um or 1 X 150 to 200um.
It is recommended to spray colour in two coats.
If coating twice, a midcoat denibbing should not be made
Because this product can be used for both semi- stable as well as stable wooden constructions, you apply two different
wet thicknesses. The colour intensity will vary.
Consumption 80 - 150 ml/m2, depending on applied wet thickness per coating, without losses.
Thinning If necessary with water max. 5 %.
Application temperature 15 - 25 °C for substrate, air and material at approx. 60 % R.H.
Drying times The drying process of the coating depends on the applied wet film thickness and can extend when using timber with a
high extract contents or drying in damp/cold conditions. During the drying process one should ensure for adequate
temperature and ventilation.
If the drying conditions are not upheld, damages within the coating cannot be warranted.
Drying at 23 °C / 50 % R.H.
Dust dry: after approx. 60 minutes
Recoatable: after approx. 4 - 6 hours waterborne
Cleaning of equipment Clean directly after use with water, if needed with washing up liquid or with ST 830.
StorageThe minimum storage stability of sealed containers is 2 years.
Storage temperature: +5 - +30 °C.
After ending of the storage time the product still can be usable, but some attributes may vary from new product.
Therefore such over-stored product has to be applied with special attention.
Opened cans must be sealed correctly! Store in a cool but frost-protected area.
Disposal Only residue emptied cans can be disposed via recycling. Liquid wastes must be disposed of according to national
regulations or according to EU-disposal key 08 01 12.
Hazard identification In accordance with EC guide lines - Material safety data sheet, point 15.
Warning Before use, read the identification and product information. Even when working with low emission products one should
take care of the customary protection measures.
General instructionsThe wood moisture content for the application of Sikkens coating systems should be between 12 % and 15 %.
According to the guidelines for window coating systems, published by the Federal German Committee for Paint and
Material Value Protection (Instruction Leaflet No. 18), of VOB, Parte, DIN 18363, and the recommendations of the
German Institute for Window Technology e.V. in Rosenheim, all wooden constructions in buildings must be coated on all
sides with at least one primer and one intermediate coat (minimum dry film thickness 30 urn) before they are
incorporated in buildings. The choice and use of the coating system, especially the colour shade, should also be taken
into account. Darker shades can increase the surface temperature (up to 80 C).
For use in a technical industrial companies and exclusively released for Sikkens systems recomondations.
VOC guideline EU limit value for this product (Kat. A/e): 150 g/l (2007)/130 g/l (2010). This product contains max. 80 g/l VOC.
Relevant information The here mentioned coating system is only an example, other systems are possible.
All external materials (i.e. fillers, tapes, sealing compounds, cleaners) must be checked for compatibility with the coating
system before use.
Please observe the relevant Technical Data Sheets or seek advice from the Sikkens sales representative or contact the
technical centre.
Coating recommendation Information on the maintenance coat:
Only waterborne coating systems may be used for the maintenance system!
Akzo Nobel Industrial Coatings Ltd Unit 4a, Mercer Way, Shadsworth Blackburn, Lanes, BB12QZ
Bus Pk
Akzo Nobel Industrial Coatings Ltd Unit 4a, Mercer Way, Shadsworth Blackburn, Lanes, BB12QZ
Bus Pk
Akzo Nobel Wood Coatings GmbH Diisseldorfer StraGe 96-100 40721 Hilden
AkzoNobel
United Kingdom Tel. +44 1254 687950 Fax. +44 1254 687960
Rep of Ireland Tel. +35 (0) 21 4220222 Fax. +35 (0) 21 4220205
Germany Tel.: +49-2103-77-800 Fax: +49-2103-77-577
"