Data sheet FEE-1M0 pages
Front End Electronics
for CCD / InGaAs / NMOS
Spectral Sensors and PDAs
In der Au 27
61440 Oberursel / Germany
FEE-1M
Phone: +49 (0) 6171 / 9758 – 0
Fax: +49 (0) 6171 / 9758 – 50
E-Mail: sales@tec5.com
Internet: www.tec5.com
Product-ID: 06107.14
Document: ds_fee-1m_108e.doc
Basic Versions for CCD / InGaAs / NMOS
FEE-1M is available in three basic versions:
• FEE-1M /CCD-x for CCD - Spectral Sensors with
tec5 Preamplifier Electronics DZA-S7030-4 (x=2) or
DZA-S9840 (x=8)
• FEE-1M /NIR-x for InGaAs - Spectral Sensors with
tec5 Preamplifier Electronics DZA-VVIR-LD (x=2) or
DZA-VVIR-HM (x=4)
• FEE-1M /NMOS-x (x=1 or d1) for MCS with
Preamplifier DZA-S3901-4 1M for Hamamatsu NMOS PDA types S3901 to S3904 or compatible, alternatively for Carl Zeiss MMS Spectral Sensor with
Preamplifier DZA-MMS 1M
The extension ‘-x’ specifies the master clock frequency
generated by FEE-1M for the Preamplifier Electronics.
Short Description
Features / Specifications
§
Functional Properties
• Generation of supply voltages for sensors and preamplifiers (not used by self powered DZA-S7030-4
or DZA-S9840)
• PDA readout clock sequencing
• Analog video signal preprocessing, A/D conversion
• Data transfer to the Interface Electronics
• Local non-volatile memory, 256 Bytes capacity
(e.g. for identification data of the sensor(s), calibration coefficients or customer specific information)
Specifications
• ADC
16 bits
• Conversion rate
(100), 500 or 1000 kSps
• Electrical Non-linearity < ±2 counts
• Temperature drift
< ±1.0 count / °C
• Offset adj. range
approx. ± 2000 counts
§
§
§
§
§
§
§
§
Fast readout control logic with ADC for
digitization of the sensors’s analog video signal
For CCD, InGaAs and NMOS PDAs
Readout rate: 100, 500 or 1000 kpixels/second
High resolution: 16 bits A/D conversion
Dynamic range: up to > 15 bits (with PDA)
On-board generation of stabilized ±5V for the
sensors from a single supply voltage (5V ±1V)
Input from device:
Preamplifier with PDA or Spectral Sensor
Output to device: tec5 Interface Electronics
(PD-ETH01V1, PD-USB01V2 or PD-PCI01V1)
PCB dimensions 87 mm x 67 mm (FEE standard)
General
The FEE-1M functions as a kind of adapter between the
sensor module and the Interface Electronics. It generates the control signals for the photodiode array of the
sensor module, preprocesses the analog video signal
and performs analog / digital conversion. The digitized
intensity values are provided as byte sequential data
stream for the Interface Electronics.
The circuit board is connected either to the PCI bus
Interface Electronics via a shielded 2 or 5m long multipin cable (PD-PCI01V1 version ‘Standard’, interface
standard ‚Interface_40’) or directly plugged on top of the
Ethernet- or USB Interface Electronics (PD-ETH01V1 or
PD-USB01V2, version ‚Embedded’, Interface standard
‘Interface_2*18’).
The sensor interface corresponds to specification ‚Sensor_Ux‘. The sensor module is connected to the FEE
using two flat ribbon cables (4 pin and 14 pin).
Basic Version
Input sensitivity
[counts/V] approx.
Standard deviation
[counts] typically
Pixel frequency
[kHz]
Readout time [ms]
Sensor (example)
[number pixels]
Power consumption [mA] typically
(@ +5V)
/CCD-2
(S703x)
3,700
/CCD-8 /NIR-2
/NMOS /NMOS
(S9840) (InGaAs) -1
-D1
3,700
13,500
17,000 17,000
3.1
(cooled)
500
15
4.0
4.0
< 2.0
1000
500 (*)
1000
100
1.9 or 2.9
(532 or
1044x64)
140
2.3
(2080
x20)
200
1.1
(512)
0.52
(512)
5.2
(512)
310
320
250
(*) up to 1MHz for Hamamatsu G9212/14 (with /NIR-4)
Detailed technical data of the different configurations
can be found in the FEE-1M Technical Documentation.
Interfaces
• Interface type ‚Sensor_Ux’ to sensor preamplifier
(MICS4 connector for analog input signal only)