TW - Wire Mesh Belt0 pages
TW
nnnnThe Model TW with wire belt can carry hot or cold
nnnnparts from ovens or freezers. Can be used in drying
nnnnoperations.
nnnnHorizontal Wire Mesh Belt Conveyor
nnnn• 3 Belt Widths
nnnnWire Mesh Belt
nnnnAdjustable MS-Type Floor Supports Available
nnnnSIZE TO ORDER Overall 1onnth"A" Leiiyiii M | Bed Length "L" | Belt Width | 12" | 18" | 24" |
Bed Width | 16" | 22" | 28" | ||
6'-1" | 5' | WEIGHTS (Lbs.) | 299 | 322 | 365 |
11-1" | 10' | 368 | 415 | 465 | |
16-1" | 15' | 461 | 525 | 593 | |
21-1" | 20' | 530 | 608 | 693 | |
26-1" | 25' | 623 | 718 | 821 | |
3T-1" | 30' | 692 | 801 | 921 | |
4T-1" | 40' | 854 | 994 | 1149 | |
5T-1" | 50' | 1023 | 1197 | 1391 | |
6T-1" | 60' | 1185 | 1390 | 1609 | |
7T-1" | 70' | 1355 | 1594 | 1862 | |
81-1" | 80' | 1517 | 1787 | 2090 | |
9T-1" | 90' | 1697 | 1979 | 2319 | |
ior-i" | 100' | 1841 | 2172 | 2547 |
OVERALL LENGTH "A"
nnnn— BED LENGTH "L"
nnnn-TAKE-UP
nnnnAll weights in catalog are conveyor weights only.
nnnnAccessories, crating, etc., are not included.
nnnnLOAD CAPACITY CHART @ 65 FPM | ||
HP | BEDWIDTHS-16"to28" | |
TOTAL LOAD (Lbs.) | ||
UP TO 50' | UPT0100' | |
y-i | 850 | 350 |
i | 1950 | 1500 |
TREAD
nnnnROLLER"
nnnnTOTALLY <£
nnnnENCLOSEDX
nnnnCHAIN GUARD \
nnnnBED WIDTH —
nnnnBELTWIDTH^
nnnn1.9" DIA.
nnnn/RETURN IDLER
nnnn'OR
nnnn2-1/8" DIA.
nnnnSNUB IDLER
nnnn^5/8" 7-3/8"
nnnnSECTION X-X
nnnn_FRAME
nnnnSPACER
nnnn• STANDARD SPECIFICATIONS
nnnnBELT-W in. x 1 in. flat galvanized wire mesh belt. Maximum product temperature 350°F.
nnnnBED—Roller bed with 1.9 in. dia. roller x 16 ga. galvanized tube spaced every 6 in. Mounted in 6 % in.
nnnnx 12 ga. powder painted formed steel channel frame bolted together with splice plates.
nnnnEND DRIVE-Located on discharge end of conveyor, chain guard on left hand side.
nnnnCROSS BRACING-Rods with turnbuckles are fastened to underside of bed to provide alignment of
nnnnbed rollers to insure correct belt tracking. Required on every other section 30 ft. bed lengths and over.
nnnnDRIVE SPROCKETS-6 in. pitch dia. multiple cast iron sprockets with
nnnnVht, in. dia. shaft 6 in. centers.
nnnnTAIL PULLEY-4 in. dia. with 1 in. dia. shaft at bearings. Sprocket at each end.
nnnnSNUB IDLER-Adjustable 2 Vts in. dia. pre-lubricated ball bearings.
nnnnRETURN IDLER-Adjustable 1.9 in. dia. pre-lubricated ball bearings.
nnnnTAKE-UP-Take-ups at tail pulley. Provides4 in. of belt take-up.
nnnnBEARINGS-Sealed, pre-lubricated, self-aligning ball bearings on drive and tail shafts. Pre-lubricated
nnnnball bearings in tread rollers.
nnnnSPEED REDUCTION-Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive sprocket.
nnnnMOTOR-VS HP-208/230/460/575V-3 Ph. 60 Hz. Totally Enclosed C-Face.
nnnnBELT SPEED-Constant 65 FPM.
nnnnCAPACITY-Maximum load per linear foot of conveyor 75 lbs. NOT TO EXCEED capacity in chart.
nnnnFLOOR SUPPORTS-Now supplied as optional equipment.
nnnn-<
nnnnO
nnnnI—
nnnnn
nnnno
nnnn-<
nnnno
nnnn70
nnnnn
nnnno
nnnnOPTIONAL EQUIPMENT
nnnnFLOOR SUPPORTS-MS Type floor supports are available with a wide range of adjustment. Specify
nnnntop of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes
nnnnin feet for lagging to floor. Knee braces recommended above MS-6 support.
nnnnBED-Slider bar in place of roller bed.
nnnnBELT-Other widths than standard, galvanized low carbon steel, bright high carbon steel or
nnnnstainless steel. 1 in.orW in.xW in. mesh
nnnnavailable. Maximum product temperature 750°F with high carbon steel belt.
nnnnBELT SPEED-Other constant and variable speeds. V-belt drive supplied on speeds under 15 FPM
nnnnand with variable speeds. Note: Capacity affected with speed change.
nnnnV-BELT DRIVE—V-belt supplied between motor and reducer.
nnnnO-RING DRIVE CHAIN-With sealed in lubricant (Recommended for applications that do not permit
nnnnregular lubrication).
nnnnCEILING HANGARS-% in. dia. x 8 ft. long unplated rods fully
nnnnthreaded. Other lengths and galvanized rods available.
nnnnMOTORS-Energy efficient, single phase, brakemotor, other characteristics. 1 HP maximum.
nnnnELECTRICAL CONTROLS-Non-reversing magnetic startersand
nnnnpush-button stations. AC variable frequency drive.
nnnnHYTROL CONVEYOR CATALOG
nnnn02012013
"