•t
•t
•t
t

Transnorm Belt Curve Conveyor

20 Belt Widths
Adjustable FSK-Type Floor Supports Available
Clipper Lacing
F.O.B. Arlington, Texas
Conveyor shown with
optional floor supports

"A"

OAW

11"

4"

CONVEYING
SURFACE

11"

GUARD RAIL
(NOT SUPPLIED AS
STANDARD EQUIPMENT)
8-1/2"
TOP OF BELT

I N C.

"
"CL" OR"
(CSW)

OW

FL

FL

O

W

FL

CONVEYING
SURFACE
WIDTH

O

OW

W

"A"
FL

"IR"
TYPE A
LEFT HAND CURVE
OUTSIDE DRIVE

TYPE B
RIGHT HAND CURVE
OUTSIDE DRIVE

TYPE C
LEFT HAND CURVE
INSIDE DRIVE

TYPE D
RIGHT HAND CURVE
INSIDE DRIVE

Applies to all degree of curves. All locations are standard for Transnorm. Specify location.

OAW
Frame
16 1/2"
18 1/2"
20 1/2"
22 1/2"
24 1/2"
26 1/2"
28 1/2"
30 1/2"
32 1/2"
34 1/2"
36 1/2"
38 1/2"
40 1/2"
42 1/2"
44 1/2"
46 1/2"
48 1/2"
50 1/2"
52 1/2"
54 1/2"

Conveying
Belt
Surface
"IR"
Width
Width
11"
10" 34"
13"
12" 32"
15"
14" 30"
17"
16" 28"
19"
18" 26"
21"
20" 36"
23"
22" 34"
25"
24" 32"
27"
26" 54"
29"
28" 52"
31"
30" 50"
33"
32" 48"
35"
34" 46"
37"
36" 44"
39"
38" 66"
41"
40" 64"
43"
42" 62"
45"
44" 60"
47"
46" 58"
49"
48" 56"

• Standard Specifications

"CL"
45°
60°
90°
180°
Radius "OR" Weight Weight Weight Weight BELT–Black Rough Top (Inverted Pyramid) Self
MOTOR– 3/4 HP Shaft Mounted Right Angle
(CS)
(Lbs.) (Lbs.) (Lbs.) (Lbs.)
Extinguishing Belt with Guide Strip
Gearmotor 208/230/460/575V-3Ph. 60 Hz (Specify
Exact Voltage).
39 1/2"
361
386
411
552
FRAME–9.45 in. deep x 40 mm x 40 mm aluminum
38 1/2"
365
390
414
567
extrusion.
BELT SPEED–Constant 65 FPM at center line of
37 1/2" 45"
365
390
415
572
conveying surface.
36 1/2"
367
392
417 DRIVE OUTSIDE
577
PULLEYS–Tapered with 1 7/16 in. dia. shaft through
35 1/2"
369
394
419
581
DRIVE
bearings. Adjustable to control belt tension. OUTSIDE
CAPACITY–Maximum load perOUTSIDE
DRIVE linear foot (measured
at center line of conveying surface) 40 lbs.
46 1/2"
380
423
466
626
BEARINGS–Sealed, pre-lubricated, self-aligning, ball
45 1/2" 57"
388
438
487
659
bearings on drive and tail pulley. Re-lube type.
FLOOR SUPPORTS–Now supplied as optional
44 1/2"
390
440
490
665
equipment. See chart below for available elevations.
67 1/2"
426
520
591
868
LEFT HAND RIGHT HAND LEFT HAND RIGHT HAND LEFT HAND
66 1/2"
428
524 RIGHT HAND
596
877
65 1/2"
431
530
601
887
90˚ CURVES
60˚ CURVES
45˚ CURVES
81"
64 1/2"
434
533
606
896
DRIVE OUTSIDE
63 1/2"
437
538
611
905
FLOOR SUPPORTS–FSK Type floor supports are
available with a wide range of adjustment. Specify
62 1/2"
439
542
616
913
BELTS–Types and styles other than standard are
top of belt elevation. Supports required at each end
85 1/2"
481
621
706
1103
available (contact factory).
and in the center of the conveyor. Holes in feet for
84 1/2"
485
627
713
1116
RIGHT braces recommended aboveLEFT HAND
lagging to floor. KneeHAND
83 1/2"
488
633
720
1129
180˚ CURVES CEILING HANGERS–Includes mouting brackets and
FSK-6 support.
105”
cross pipes only.
82 1/2"
491
639
726
1141
81 1/2"
494
644
732
1152
BELT SPEED–Up to 250 FPM (shaft mounted), 251 GUARD RAILS–3 in. to 24 in. tall available for all
600 FPM (timing belt),
80 1/2"
497
649
738
1164
sizes.

• Optional Equipment

NOTE: Capacity affected with speed change, see
chart above. Higher speeds available, contact
factory.
DRIVE LOCATION–Specify.

MOTORS–Other HP available, 5 HP maximum
(contact factory).

Hytrol Conveyor Catalog
02012013

CO M P A N Y ,

1-1/2"

90˚

CO N V E Y O R

The Model TS1500-140 provides a positive flow of
products by means of a belt, driven by tapered pulleys.
Conveyor is versatile in that it can transport a wide
variety of products. Available in 45°,60°, 90°, and 180°
turns. Other degrees available. Contact Transnorm.

HY TR O L

TS1500-140

ELECTRICAL CONTROLS–Non-reversing magnetic
starters and push-button stations. AC variable
frequency drive.
CUSTOM COLORS–Available (contact factory).
Paint chip must be provided.

2.1