EtherCAT®-Slave solution for IPC@CHIP®0 pages

Information sheet: EtherCAT®-Slave solution for IPC@CHIP®
®

EtherCAT-Slave
SC123/SC143

solution for IPC@CHIP

®

®

» based on EtherCAT -Slave FPGA from
Altera
®
®
» EtherCAT protocol stack for IPC@CHIP
RTOS as C-library
®
» support of the EtherCAT profiles CoE
(CANopen) and FoE (File Access)
» free programmability in C/C++ and CoDeSys
IEC61131-3
» free usability of all interfaces and software
®
functions of the IPC@CHIP SC123/143

Whether you need an Embedded-Controller for the
®
implementation of an intelligent EtherCAT -Slave
®
or if you wish to equip an IPC@CHIP based
®
device additionally with an EtherCAT -Slave
®
interface – with the choice of the IPC@CHIP
controller platform you definitely have the right
solution for your decentralised automatization
requirements.
Intelligent and flexible
®

With the implementation of the IPC@CHIP your
®
local EtherCAT device benefits automatically from
®
the advantages of the IPC@CHIP EmbeddedController. The flexible programming and the
comprehensive equipment provide for an
adaptable implementation into all automated
applications with decentralised pre-processing.
Programmable in C/C++ and IEC61131-3
The multitasking real-time operating system of the
®
IPC@CHIP allows for a free programming in
C/C++ and CoDeSys IEC61131-3. You can flexibly
adapt the IEC61131-3 run-time system to the
requirements of your intelligent slave-application.

®

EtherCAT -Slave
EC01

Development-Kit

DK61-

» Development-board based on Beckhoff
®
EtherCAT -Stamp
FB1120,
directly
®
attachable on IPC@CHIP Development
board DK60
®
®
» EtherCAT – protocol stack for IPC@CHIP
RTOS as C-library
» application sample in C and IEC61131-3
» documentation and support

IS_EtherCAT _EN_V5.PDF
© Copyright Beck IPC GmbH

Communicative
®

With the implementation as EtherCAT -Slave even
®
the comprehensive interfaces of the IPC@CHIP
remain fully functional and can ideally be used e.g.
®
in
gateway
solutions.
The
IPC@CHIP
®
SC123/SC143 as EtherCAT -Slave furthermore
additionally provides the following local interfaces:
Moreover you can use 31 I/O-Lines as well as the
®
Address-/Data bus of the IPC@CHIP for the
connection of direct I/O or additional peripheral
devices.
Development-Kit for the fast and cost-efficient
development
®

For development of intelligent IPC@CHIP
®
SC123/SC143 based EtherCAT -Slaves the
Development-Kit DK61-EC01 is at your disposal.
This enlarges the basic functionality of the
®
IPC@CHIP Development-Kit DK61 in all functions
and components needed for a quick and cost®
efficient realisation of your EtherCAT -Slave
application.
Easy start-up in only a few minutes
If you already own a Development-Kit DK61, you
®
can put the EtherCAT -Slave-Development-Kit into
operation in a few minutes and integrate it into an
®
existing EtherCAT network as an operating slave.
For that purpose the Development-Kit includes
ready-to-use demo applications in C and
IEC61131-3.
®

For more information about the IPC@CHIP Platform check our website at: http://www.beckipc.com
EtherCAT® is registered trademark and patented technology, licensed
by Beckhoff Automation GmbH, Germany.

Beck IPC GmbH
Nauborner Straße 184
35578 Wetzlar/Germany

E-Mail: info@beck-ipc.com
www.beck-ipc.com