LOADING
جک تخت هیدرولیکی
چگونه این محصول را خریداری کنم؟
درخواست قیمت
درخواست مشاوره و مدارک فنی
پرسش
خدمات خرید VIP
شما می توانید از سرویس رایگان نمایشگاه استفاده نموده و درخواست خود را مستقیما به شرکت سازنده ارسال نمایید و پس از دریافت قیمت و با ورود اطلاعات به " ماشین محاسبه قیمت ریالی " از قیمت ریالی کالا بصورت تخمینی مطلع شوید . اگر مایلید مکاتبه با شرکت سازنده ، تبادل اطلاعات و دریافت قیمت ارزی و ریالی توسط کارشناسان این مجموعه انجام شود لطفا از این طریق اقدام فرمایید. استفاده از این سرویس مستلزم پرداخت هزینه است . برای دریافت اطلاعات بیشتر با تلفن 41995 تماس حاصل فرمایید.
ادامه
ادامه
در صورتی که قیمت ارزی محصول را در اختیار دارید پس از عضویت و ورود به سایت می توانید فرم مربوطه را تکمیل و به همراه تصویر پرفورمای شرکت سازنده ارسال نمایید تا کارشناسان ما در اسرع وقت نسبت به محاسبه هزینه های حمل و ترخیص و صدور پیش فاکتور ریالی اقدام نمایند. هزینه استفاده از این سرویس برای هر درخواست 25 یورو می باشد. صنایع معظم در صورت تمایل به استفاده از این خدمات می توانند بدون نیاز به عضویت و پرداخت هزینه درخواست خود را به همراه کپی پرفورمای شرکت سازنده به ایمیل enquiry@iranindustryexpo.com و یا فاکس 88206264 بنام شرکت مهندسی و بازرگانی مشگاد ارسال نمایند.
در صورت عقد قرار داد مبلغ دریافتی به حساب خریدار عودت می شود.
ادامه
افزودن به لیست علاقه مندی ها
سایر سازندگان این محصول
درخواست قیمت ریالی
اگر مجموعه شما جزو صنایع مادر و معظم در فیلد پالایشگاه ، پتروشیمی ، حفاری ، نیروگاه ، معادن و فلزات ، خودروسازی ، تولید مواد غذایی و دارویی و.... می باشد لطفا درخواست خود را بر روی سربرگ به فاکس 88206264 و یا ایمیل enquiry@iranindustryexpo.com بنام شرکت مهندسی و بازرگانی مشگاد ارسال فرمایید.
کارشناسان این مجموعه در اسرع وقت با شما تماس خواهند گرفت .
بازدیدکننده محترم، از اینکه سایت ایران اینداستری را برای منابع یابی انتخاب کرده اید، از شما سپاسگزاریم.
اطلاعاتی برای نماینده شرکت BOVIAR SRL در ایران یافت نشد.
لطفا با انتخاب هر یک از بخش های فوق، درخواست خود را ارسال فرمایید تا توسط واحد بازرگانی ایران اینداستری اکسپو بررسی شود.
مشخصات فنی
-
Other characteristics:
flat
-
Type:
hydraulic
Flat jacks are mainly used in the diagnosis of buildings and masonry with the purpose of establishing experimentally the actual static conditions of the structure under investigation. Other possible applications regard the measurement of stress in situ (e.g. in tunnels lining and in bridge piers).
The single-jack test methodology is based on the variation of the stress state in a point of the structure under examination due to a plane cut executed in the direction perpendicular to the surface. The stress release causes the cut to be closed to an extent which is assessed through convergency measurements between one or more points, situated in a symmetrical position with respect to the cut itself by using a high-precision strain gauge (see Mayes strain gauge). A special flat jack is then inserted within the cut and gradually put under pressure with a special hydraulic pump (see M2H16 Glötzl hand pump) until the previously measured convergency is eliminated. In these conditions the pressure within the jack is equal to the pre-existing force on the masonry, minus a constant that takes into account the relation between the area of the load jack and the area of the cut and the jacks stiffness coefficient (Km).
Two parallel jacks installed at about 50 cm from one another are used and the volume of material delimited by them is submitted to a mono-axial compression test to identify the deformability characteristics.
The employment of flat jacks can involve both a recovery installation and a disposable installation: in this case the jack is cemented to the cut and will serve for the medium and long-term measurement of the pressure in the point of installation.
The single-jack test methodology is based on the variation of the stress state in a point of the structure under examination due to a plane cut executed in the direction perpendicular to the surface. The stress release causes the cut to be closed to an extent which is assessed through convergency measurements between one or more points, situated in a symmetrical position with respect to the cut itself by using a high-precision strain gauge (see Mayes strain gauge). A special flat jack is then inserted within the cut and gradually put under pressure with a special hydraulic pump (see M2H16 Glötzl hand pump) until the previously measured convergency is eliminated. In these conditions the pressure within the jack is equal to the pre-existing force on the masonry, minus a constant that takes into account the relation between the area of the load jack and the area of the cut and the jacks stiffness coefficient (Km).
Two parallel jacks installed at about 50 cm from one another are used and the volume of material delimited by them is submitted to a mono-axial compression test to identify the deformability characteristics.
The employment of flat jacks can involve both a recovery installation and a disposable installation: in this case the jack is cemented to the cut and will serve for the medium and long-term measurement of the pressure in the point of installation.