ادامه
در صورتی که قیمت ارزی محصول را در اختیار دارید پس از عضویت و ورود به سایت می توانید فرم مربوطه را تکمیل و به همراه تصویر پرفورمای شرکت سازنده ارسال نمایید تا کارشناسان ما در اسرع وقت نسبت به محاسبه هزینه های حمل و ترخیص و صدور پیش فاکتور ریالی اقدام نمایند. هزینه استفاده از این سرویس برای هر درخواست 25 یورو می باشد. صنایع معظم در صورت تمایل به استفاده از این خدمات می توانند بدون نیاز به عضویت و پرداخت هزینه درخواست خود را به همراه کپی پرفورمای شرکت سازنده به ایمیل enquiry@iranindustryexpo.com و یا فاکس 88206264 بنام شرکت مهندسی و بازرگانی مشگاد ارسال نمایند.
در صورت عقد قرار داد مبلغ دریافتی به حساب خریدار عودت می شود.
ادامه
اگر مجموعه شما جزو صنایع مادر و معظم در فیلد پالایشگاه ، پتروشیمی ، حفاری ، نیروگاه ، معادن و فلزات ، خودروسازی ، تولید مواد غذایی و دارویی و.... می باشد لطفا درخواست خود را بر روی سربرگ به فاکس 88206264 و یا ایمیل enquiry@iranindustryexpo.com بنام شرکت مهندسی و بازرگانی مشگاد ارسال فرمایید.
کارشناسان این مجموعه در اسرع وقت با شما تماس خواهند گرفت .
بازدیدکننده محترم، از اینکه سایت ایران اینداستری را برای منابع یابی انتخاب کرده اید، از شما سپاسگزاریم.
اطلاعاتی برای نماینده شرکت ROLLAND در ایران یافت نشد.
لطفا با انتخاب هر یک از بخش های فوق، درخواست خود را ارسال فرمایید تا توسط واحد بازرگانی ایران اینداستری اکسپو بررسی شود.
-
Applications:
draining, test
-
Media:
water, hydraulic
-
Other characteristics:
open
-
Type:
positive-displacement
• Rcl/2 inlet unions
• RC1/2 lockable ball valves
• 3 mm flow restrictor
• 0-16 bar glycerine gauges c/w no loss connectors
• 1/2" check valves in copper bypass line
• 0-14 bar pressure switch (double) for duty and stand by pumps
• 0-14 bar pressure switch for jockey pump
• 1/2" galvanised tube and fittings
Installation & maintenance
• Assembly to be located where it will not be subjected to freezing or extreme temperatures. All electrical
connections to be made by qualified staff.
• Pressure switch can be set after installation with system at operating pressure. Close the top inlet valve
and slowly open the bottom test valve to reduce gauge pressure to the desired level. Close test valve and
adjust pressure switch. Double switch units require the same procedure but the switch not being set must
be disconnected from the circuit at the pressure switch plug.
• Alternatively, these double switched units can be connected via a spring loaded inhibitor switch which will
then accommodate both initial setting and weekly tests without the need to disconnect the switch that is
not being set or tested.
• To test pump operation, close the top inlet valve and slowly open bottom test valve to start pump. Top
inlet valve to be in the open position for normal operation
• Unit is designed to be maintenance free. However pressure switches and gauges can be replaced by
isolating the pump, closing top inlet valve and draining the unit via bottom test valve.