LOADING
سیستم نوری
ABIS II
چگونه این محصول را خریداری کنم؟
درخواست قیمت
درخواست مشاوره و مدارک فنی
پرسش
خدمات خرید VIP
شما می توانید از سرویس رایگان نمایشگاه استفاده نموده و درخواست خود را مستقیما به شرکت سازنده ارسال نمایید و پس از دریافت قیمت و با ورود اطلاعات به " ماشین محاسبه قیمت ریالی " از قیمت ریالی کالا بصورت تخمینی مطلع شوید . اگر مایلید مکاتبه با شرکت سازنده ، تبادل اطلاعات و دریافت قیمت ارزی و ریالی توسط کارشناسان این مجموعه انجام شود لطفا از این طریق اقدام فرمایید. استفاده از این سرویس مستلزم پرداخت هزینه است . برای دریافت اطلاعات بیشتر با تلفن 41995 تماس حاصل فرمایید.
ادامه
ادامه
در صورتی که قیمت ارزی محصول را در اختیار دارید پس از عضویت و ورود به سایت می توانید فرم مربوطه را تکمیل و به همراه تصویر پرفورمای شرکت سازنده ارسال نمایید تا کارشناسان ما در اسرع وقت نسبت به محاسبه هزینه های حمل و ترخیص و صدور پیش فاکتور ریالی اقدام نمایند. هزینه استفاده از این سرویس برای هر درخواست 25 یورو می باشد. صنایع معظم در صورت تمایل به استفاده از این خدمات می توانند بدون نیاز به عضویت و پرداخت هزینه درخواست خود را به همراه کپی پرفورمای شرکت سازنده به ایمیل enquiry@iranindustryexpo.com و یا فاکس 88206264 بنام شرکت مهندسی و بازرگانی مشگاد ارسال نمایند.
در صورت عقد قرار داد مبلغ دریافتی به حساب خریدار عودت می شود.
ادامه
افزودن به لیست علاقه مندی ها
سایر سازندگان این محصول
درخواست قیمت ریالی
اگر مجموعه شما جزو صنایع مادر و معظم در فیلد پالایشگاه ، پتروشیمی ، حفاری ، نیروگاه ، معادن و فلزات ، خودروسازی ، تولید مواد غذایی و دارویی و.... می باشد لطفا درخواست خود را بر روی سربرگ به فاکس 88206264 و یا ایمیل enquiry@iranindustryexpo.com بنام شرکت مهندسی و بازرگانی مشگاد ارسال فرمایید.
کارشناسان این مجموعه در اسرع وقت با شما تماس خواهند گرفت .
بازدیدکننده محترم، از اینکه سایت ایران اینداستری را برای منابع یابی انتخاب کرده اید، از شما سپاسگزاریم.
اطلاعاتی برای نماینده شرکت Steinbichler Optotechnik در ایران یافت نشد.
لطفا با انتخاب هر یک از بخش های فوق، درخواست خود را ارسال فرمایید تا توسط واحد بازرگانی ایران اینداستری اکسپو بررسی شود.
مشخصات فنی
-
Options:
surface inspection
ABIS II - Defect recognition during production process
The majority of defects that can occur during the production process are invisible at the early stages of manufacture. These minute surface defects become visually perceptible later on, however, when subsequent work steps such as paint work have been completed. At that point in time, they can only be remedied using expensive corrective measures.
To achieve a high surface quality under the aspect of cost optimization, a wide range of defect types needs to be detected. The reliable and early detection combined with an objective evaluation and classification of defects, such as dents, bumps, sink marks, waviness, constrictions, cracks, etc., is necessary since the costs of removing these defects increase drastically with the progress of work within the production cycle (press shop, body shop, paint shop, final assembly). Consequently, particularly the rework of defects that have been propagated throughout the production process constitutes a substantial factor with regard to manpower and time. It thus has a considerable influence on the economic efficiency of the manufacturing process.
ABIS II an optical sensor system that is available in different versions and system concepts allows the fast, reliable and ultra-accurate detection of not only 3D defects on the inspected part (e.g. dents, bumps, sink marks, waviness, constrictions or cracks), but also of contrast-sensitive defects (e.g. scrat¬ches, adhesive residues, dust and dirt) using the new contrast sensor upgrade.
Time-consuming and thus expensive re¬work in subsequent process steps, e.g. at the finish belt, can be efficiently reduced.
The majority of defects that can occur during the production process are invisible at the early stages of manufacture. These minute surface defects become visually perceptible later on, however, when subsequent work steps such as paint work have been completed. At that point in time, they can only be remedied using expensive corrective measures.
To achieve a high surface quality under the aspect of cost optimization, a wide range of defect types needs to be detected. The reliable and early detection combined with an objective evaluation and classification of defects, such as dents, bumps, sink marks, waviness, constrictions, cracks, etc., is necessary since the costs of removing these defects increase drastically with the progress of work within the production cycle (press shop, body shop, paint shop, final assembly). Consequently, particularly the rework of defects that have been propagated throughout the production process constitutes a substantial factor with regard to manpower and time. It thus has a considerable influence on the economic efficiency of the manufacturing process.
ABIS II an optical sensor system that is available in different versions and system concepts allows the fast, reliable and ultra-accurate detection of not only 3D defects on the inspected part (e.g. dents, bumps, sink marks, waviness, constrictions or cracks), but also of contrast-sensitive defects (e.g. scrat¬ches, adhesive residues, dust and dirt) using the new contrast sensor upgrade.
Time-consuming and thus expensive re¬work in subsequent process steps, e.g. at the finish belt, can be efficiently reduced.