FZ, FU, FZB, FUB0 pages
Tubular fixed resistors
Type series FZ / FU
Type series FZB / FUB
12 – 1000 W for integration
12 – 300 W with threaded rod
IP
E
00
Cemented (FZ) and uncemented (FU) wirewound tubular fixed resistor, degree
of protection IP00.
Type series F.B additionally with mounted threaded rod, fixing vertically to
mounting surface.
Variable connections at the soldering, fast-on or screw clips* on the resistor.
FZ 100x24ST
(with fast-on adjustable clip)
*Particular specifications for „low ohmic values“ – for details please look on the following page
Technologies
Type designation (standard)
Types with soldering connections (4,8x0,5)
connection directly at the resistor
optional, depending on construction
size with screw, fast-on or soldering
connection
adjustable clips (Ags.) available
size
D=16
(please mind the hints on this page and
on the following one)
with type series F.B.. only small
mounting space is needed
mounting in switch cabinets
You will find indications for the
relationship between load capacity and
temperature on the surface as well as
for the dimensioning of the resistor at
short term load in chapter “Technical
Details”, pages T103E-T108E.
Application
As ballast, limiting, filter or series
resistors etc. for integration into devices
and customised units. Our type series
F.B.. is very well applicable in switch
cabinets. We fix the threaded rod for you
in a space-saving way. Efficient use in
your manufacturing systems.
Special design
various tube sizes as well as lower
and higher ohmic values on request
beginning with size D=24 also with
temperature switch (TS)
with fast-on connections 6,3 x 0,8
soldering connections, pretinned
FRIZLEN GMBH U. CO KG.
clips with 1 Ags.
FZ..x16AE
with n Ags.
FZ..x16AnE
Types with fast-on connections (6,3x0,8, also solderable)
size
D=24
D=35
D=45
We provide M3 screw connections for
construction sizes with diameters D=16
and M4 with D=24/35/45 M5 with D=65.
Also fast-on connections (6,3x0,8) are
available for sizes with D=24/35/45.
For sizes with D=16 the soldering
connections can also be used as fast-on
connections (4,8x0,5).
You will find the electrical and
mechanical data on the next page.
without adjustable
(Ags.)
FZ..x16A
without adjustable
(Ags.)
FZ..x24S
FZ..x35S
FZ..x45S
clips with 1 Ags.
FZ..x24ST
FZ..x35ST
FZ..x45ST
with n Ags.
FZ..x24SnT
FZ..x35SnT
FZ..x45SnT
Types with screw connections (M3 / M4 / M5)
size
D=16
up to
D=65
without
(Ags.)
FZ..x16
....
FZ..x65
adjustable
clips with 1 Ags.
FZ..x16F
....
FZ..x65F
with n Ags.
FZ..x16 Fn
....
FZ..x65 Fn
Hints for the versions with adjustable clips
For the cemented fixed resistors with adjustable clip we decrease the available
maximum ohmic value. Since otherwise while adjusting the clip, the danger of
breaking the wire would be too large because of too thin wires. The adjustable
clip may only be adjusted in a condition free of voltage and after sufficient
loosening and cooling. All the adjustable clips of our fixed resistors in tubular
version are equipped with silver contacts. When selecting please consider that
the maximum surface temperature (ST) should not exceed 300°C.
Please consider as well that the resistance value may be reduced with versions
where several adjustable clips are combined, especially in the lower range of
ohmic values and with short tube lengths. In that case we have to select a
higher total ohmic value.
Example of dimensioning and selection of a specific unit:
Adjustable power resistor for mounting into a switch cabinet with 2 additional taps:
continuous dissipation 150 W; resistance value 100 ; rating 110 V DC, mounting
by threaded rod on mounting plate, adjustable resistance taps by 2 adjustable clips,
connection at fast-on clips,
Selected:
FZB 200 x 35 S2T – 100 with continuous dissipation 150 W
Alternatively: FZB 160 x 45 S2T – 100 (continuous dissipation also 150W)
FZB 200x35
S2T
-
100
ohmic value 10%
with fast-on clips and 2 fast-on adjustable
clips
according to list
type series (FZ.. is standard)
TEL: 07144/8100-0 FAX: /207630
Subject to alteration
info@frizlen.com
r03
T109E
"