DSE5310-53200 pages

® DSECONTROL®
MONITORING
WITH
INTELLIGENCE.
SPECIFICATION
DC SUPPLY
8 V to 35 V continuous
CRANKING DROPOUTS
Able to survive 0V for 50mS, providing the
supply was at least 10V before dropout and
supply recovers to 5V
AUXILIARY OUTPUTS 1-3
5A DC at supply voltage
AUXILIARY OUTPUTS 4 & 5
(DSE5320 only)
8 A AC rated volt-free relay
MAXIMUMOPERATING CURRENT
400mA at 12V, 200mA at 24V
STANDBY CURRENT
(when in auto)
230mA at 12V, 120mA at 24V
SLEEPMODE CURRENT
70mA at 12V, 45mA at 24V
MODULE DIMENSIONS (WxH)
240mm x 172mm
9.4” x 6.8”
PANEL CUT-OUT (WxH)
220mm x 160mm
8.7” x 6.3”
MAXIMUMPANEL THICKNESS
8mm
0.3”
The DSE5310 is an Automatic
Start ControlModule designed to
automatically start and stop diesel
and gas generating sets that
include non electronic and
electronic engines. Themodule
also provides advanced engine
monitoring and protection features.
Themodule has the ability to
monitor under speed, over speed,
charge failure, emergency stop,
low oil pressure, high engine
temperature, fail to start, fail to
stop, under/over generator volts,
over current, under/over generator
frequency, low/high DC battery
volts, low fuel alarmand loss of the
speed sensing signal. Themodule
displays fault conditions on the
LCD display and via the LED
indicators on the front.
The DSE5320 is an Automatic
Mains (utility) Failure Control
Module and includes all the
features of the DSE5310 plus the
ability to monitor a mains (utility)
supply. Upon detection of a mains
(utility) failure the module
automatically starts the
generating set. Once the mains
(utility) power has been restored
the module instructs the
generating set to stop.
Both modules include RS232 or
RS485 communication
capabilities for linking to a PC,
sending SMS messages and
interfacing with new and existing
building management systems.
FEATURES
• Automatic start
• Automatic load transfer
• Automatic mains (utility) failure
detection (DSE5320 only)
• Electronic engine connection
• RS232 or RS485 remote
communications (to be specified
on ordering)
• Modbus RTU
• Analogue inputs
• Audible alarm indication
• Back-lit character & 4-line text
LCD display
• Configurable alarms & timers
• Configurable auxiliary inputs
• Digital inputs
• Emergency stop functions
• Engine history event log
• Engine exercise mode
• Engine protection
• Front panel mounting
• Front panel programming
• Full engine diagnostics
• Generator operating status
warning
• LCD alarm indication
• LED alarm indication
• Manual start
• Multiple language options
• PC configurable
• PIN protected programming
• Power save mode
• Remote monitoring
• SMS messaging
BENEFITS
• Full integration into new & existing
building management systems
• Full engine protection &
instrumentation without the need
for additional senders (Electronic
engines only)
• In-built engine diagnostics
removes the requirement for
service equipment
• License free PC software
• Remote module control and
monitoring using comprehensive
DSE PC software
• Modules improve the life cycle of
engine starter motors
• On-site and remote module
configuration
• Modules send SMS messages to
engineers to notify specific engine
problems (GSM Modem and SIM
Card required)
• User-friendly set-up and button
layout
OPERATION
The modules are operated using the
front STOP, AUTO and MANUAL
push buttons. The DSE5320 also
includes a TEST button. An additional
push button allows the user to scroll
through the LCD display.
CONFIGURATION
The modules can be configured
using the front panel buttons or the
DSE810 interface and PC software.
DSE5310 & DSE5320
AUTO START & AUTOMAINS FAILURE CONTROLMODULES (ELECTRONIC ENGINE ENABLED)
ELECTRONIC ENGINE CAPABILITY
DSE5310 DSE5320