BMR - advanced p.f. regulator & meter and harmonic distorsion series0 pages
MU 03.14.It-Ing REV.0
03/2003
Digital Graphic Display
ALARMS indication
Segnalazione allarmi
Display grafico
Automatic / Manual selector
Selettore Automatico /
Manuale
Setting:
Display select
Regolazione:
“!” increase
“!” incremento
“"” reduction
Selezione grandezze
Display
“"” riduzione
“BMR” – Regolatore di potenza reattiva &
“BMR” - ADVANCED P.F. Regulator &
misuratore di correnti armoniche
METER and Harmonic distortion series
GENERALITA’: BMR è un regolatore automatico di potenza reattiva basato
su un circuito di controllo a microprocessore ed un misuratore della
distorsione armonica totale in corrente, che svolge funzione di protezione
degli impianti. Lo strumento controlla 6÷12 batterie ed utilizza filtri
d'ingresso che consentono il funzionamento e la corretta visualizzazione,
anche in presenza di forte distorsione armonica.
Caratteristiche principali
Funziona su linee trifase prendendo come riferimento misure
monofase. L’inserzione è in quadratura (prelievo del segnale di tensione da
due fasi e quello di corrente dalla terza) e può funzionare su linee di
distribuzione in bassa od anche in media tensione, prendendo i segnali dai
trasformatori amperometrici e voltmetrici.
Con i regolatori di questa serie, non è più necessario verificare il
senso di circolazione della corrente proveniente dal T.A., poiché la
direzionalità del segnale comporta un adattamento automatico della
modalità di lettura da parte del microprocessore. Inoltre è possibile la
memorizzazione manuale delle batterie, le quali in funzionamento
automatico permangono inserite indipendentemente dallo sfasamento
rilevato, mentre le altre vengono modulate.
ll regolatore basa il proprio funzionamento sulla logica lineare
(inserzione o disinserzione delle batterie in successione numerica partendo
dalla prima) o binaria (inserzione basata sul valore medio della potenza
reattiva misurata nel periodo di ritardo).
Altre caratteristiche: funzione quattro quadranti per la misura
dello sfasamento anche in presenza di Energia attiva generata ed
indicazione errato collegamento del T.A.
Funzioni impostabili a display in sede di taratura:
1. Valore del Cosfì medio desiderato tra i valori 0,80 IND e 0,80 CAP.
2. Valore C/K.
3. Rapporto di trasformazione del T.A. tra 5/5 e 9999/5
4. Soglia di allarme THD(i)%
5. Ritardo di inserzione e disinserzione batterie: 1 ÷ 999"
6. Numero delle batterie utilizzate dal regolatore tra 6 ÷ 12
7. Logica d’inserzione: lineare o binaria.
Allarmi con contatto NC pulito in morsettiera:
Mancata alimentazione, Mancato rifasamento (basso cosfì), Sovratensione,
Sovracorrente, Bassa corrente o Corrente nulla nel circuito amperometrico,
Sovratemperatura (50°C), Superamento della soglia di THD(i)%
programmata, Autoreset in presenza di microinterruzioni.
GENERAL FEATURES: BMR is an automatic reactive power
microprocessored regulator & meter, and harmonic distortion series.
The BMR control up to 12 banks and is equipped with an input filter
which allows correct operation and display even in presence of
harmonics on the mains.
Main characteristics
It works on three-phase networks, with single phase
measurement voltage signal (from two phases) and current signal
from the third phase.
It can operates on low voltage and medium voltage
networks throughout voltage and current transformers.
The regulators are able to detect automatically the current
phasing of the C.T. It is not necessary to ensure correct polarity
connections as with other Power Factor Regulators.
It is possible the manual insertion of the bank: in automatic
operation the “stored” output are always on, the remaining output are
working.
The regulator operates with linear logic (switch on or
switch off of the banks always starts from the first one) or binary logic
(steps switching is based on the average value of the reactive power
consumption of the load during the switching delay time).
Other
characteristics: automatic connection recognition (including inverted
C.T.) and working with generative and regenerative loads (fourquadrant operation).
Setting availables:
1. Average P.F. value setting between 0,8 lag and 0,8 lead.
2. C/K value setting.
3. CT ratios available between 5/5 and 9999/5.
4. THD(i)% alarm threshold
5. Switching step delay: 1 ÷ 999 seconds
6. Number controlled banks: from 6 to 12
7. Logic to operates: linear or binary logic
Alarms with volt free NC contact in terminal blocks for:
Supply failure, Low P.F. value, Over voltage, Over current, Minimum
current or Zero current of the C.T. secondary, Over temperature,
Distortion exceeds the threshold de THD(I)%, Auto-reset in case of
power outage longer than 40ms.
DONNES TECHNIQUES
TECHNICAL DATA
1