عضویت 
ورود اعضا
راهنمای خرید
IGD8410 pages
IGD841
Hybrid Integrated
Isolated N-Channel
IGBT Driver
Electrical Specications
Key Features:
Absolute Maximum Ratings, TA = 25 ºC unless otherwise noted.
• Internal OptoCoupler
• 30 kV/µS CMR
• VISO = 3,750V
• One Supply Drive Topology
• Compact SIP Package
• Short Circuit Protected
• Fault Signal Output
• Switching Freq. to 20 kHz
• Compatible With EXB841
Parameter
Conditions
Typ.
Max.
Units
Supply Voltage
VCC
DC
25
VDC
Input Voltage
VIN
See Note 3
50
VDC
IIN
See Note 4
25
mA
Input Current
IGON
Output Current
IGOFF
Isolation Voltage
VISO
Junction Temperature
Pulse Width 2µS, Frequency Ϲ 20 kHz
-5.0
Sine Wave Voltage 50 Hz/ 60 Hz , 1 Min
3,750
VAC
ºC
-20
+70
ºC
-40
TST
• 600V Series IGBT (up to 600A) Fault Output Current
IFO
See Note 5
• 1200V Series IGBT (up to 400A)
Electrical Characteristics, TA = 25 ºC, VCC = 15 VDC unless otherwise noted.
• 1700V Series IGBT (up to 200A)
Parameter
Conditions
Supply Voltage
VCC
Recommended Range
Reverse Bias Supply Voltage
VRB
+125
ºC
20
mA
Max.
Units
f
Recommended Range
Min.
Typ.
14
15
VDC
-5
VDC
Recommended Range
Switching Frequency
Gate Resistor
0
20
15
IIH
Recommended Range
kHz
⍀
2
RG
Input CMR
“H” Input Current
A
150
TOP
Storage Temperature
+5.0
TJ
Operating Temperature
Recommended For:
Min.
30
10
16
kV/µS
20
mA
“H” Output Voltage
VOH
VCC = 20V
14
VDC
“L” Output Voltage
VOL
VCC = 20V
-5
VDC
“L-H” Propagation
TPLH
IIH = 16 mA
0.5
1.0
µS
TR
IIH = 16 mA
0.6
1.0
µS
TPHL
IIH = 16 mA
1.0
1.3
µS
TF
IIH = 16 mA
0.4
1.0
µS
VOCP
VCC = 20V
8.5
“L-H” Rise Time
“H-L” Propagation
“H-L” Fall Time
Protection Threshold Voltage
Protection Reset Time
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Fault Output Current
TTIMER
IFO
1.0
1.4
VDC
2.0
mS
5.0
See Note 6
mA
Controlled Time Detect
TTRIP1
Short Circuit 1, See Note 7
2.6
µS
Soft Turn-Off Time
TOFF2
See Note 8
5.0
µS
SC Detect Voltage
VSC
Collector Voltage of Module
15
Notes:
1. Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
2. ”H” = high level signal. “L” = low level signal.
3. The voltage applied to pin 15.
4. The current measured between pins 15 and 14.
5. The current at pin 5.
6. The current at pin 5. R2 = 4.7 k⍀.
7. Pin 6 м 15 VDC.
8. Pin 6 м 15 VDC.
www.micropowerdirect.com
VDC
"
