Model RODI-T2 and RODI-T2-H RO+Type II0 pages
Model RODI-T2 and RODI-T2-H
RO+Type II
Features & Benefits
Availability
Product A vailability
♦ Meets UL, CSA, and CE Mark Specs.
AQUA SOLUTIONS Model
RODI-T2 and RODI-T2-H Reverse
Osmosis plus Type 2 DI Systems
dispense 2-15 Megohm-cm Type
II or Type III Reagent Grade DI
water at a flow rate of 4-5 LPM.
♦ Produces 2-15 Megohm-cm DI water
from ordinary tap water.
♦ Includes purity monitor with flashing
red LED alarm.
♦ Price includes built-in sediment and
activated carbon prefilter cartridge.
♦ Prefilter cartridge and DI modules can
be replaced in less than 5-minutes.
The systems include built-in 10 or
20 LPH reverse osmosis (RO)
pretreatment to reduce operating costs by as much as 90%, while
allowing the system to run on virtually any quality potable water. The RO
purified water is stored in a pressurized storage tank.
♦ Power supply accepts 100-240 VAC,
50/60 Hz, at 2.5 Amps.
Model RODI-T2 includes 1 installed plus 1 spare 2613DI module. The
High-Capacity Model RODI-T2-H includes 2 installed plus 1 spare
2618DI module.
♦ Safe, low-voltage (12 VDC) internal
operation.
A variety of dispensing options are available, including Teflon Remote
Dispensers, Gooseneck Faucets, and various outlet valves.
♦ User installable & serviceable.
When exhausted, the DI modules are returned to the factory where they
are refilled with ion exchange (“DI”) resin. The combination sediment
and activated carbon prefilter cartridge and DI modules can be replaced in less than 5-minutes.
♦ Made in the USA.
Valve
Optional Blending Valve Upgrade
RO-T2BV
ROIncludes a built in blending valve and
additional conductivity sensor. This upgrade
allows the user to manually adjust the purity
of the product water to < 1 megohm-cm by
mixing RO water with DI water. This is ideal
for feed water to humidity chambers and
glassware washers that could be damaged
by aggressive, high resistivity DI water.
AQUA SOLUTIONS INC.
SOLUTIONS,
8 Old Burnt Mountain Road
Jasper, GA 30143 USA
Phones:
706-692-9200
800-458-2021
Fax:
706-692-9203
E-mail:
mail@AquaA.com
Internet:
www.AquaAl.com
The RODI-T2 and RODI-T2-H RO+DI systems are self-contained units,
with the cabinet measuring just 20” wide by 20” high by 12” deep. The
systems require tap water, a drain, and a grounded 100-240 VAC, 5060 Hz electrical outlet in order to operate. They can be bench, shelf or
wall-mounted up to 20 feet away from the points of use.
An LCD purity monitor provides a continuous readout of the purified
water quality in micro-seimens/cm. The monitor’s red LED flashes
whenever the water quality falls below 0.5 MicroSeimens/cm (2 Megohm-cm). The monitor can be located anywhere within ~6 feet of the
system.
During operation, a quiet, 12 VDC pump continuously circulates purified
water through the DI modules and purity monitor on its way out to the
points of use, and back into the system. The quality of the purified water
is maximized by this recirculation process, which does not diminish the
capacity of the DI modules.
These systems are ideally suited for providing high-quality DI
water to laboratory analyzers at competitive prices!
-1-
Brochure Number: RODI-T2
"