AIRDATAâ„¢ MULTITEMP0 pages

AIRDATA™ MULTITEMP
MULTIPOINT TEMPERATURE TEST KIT
MT-440K Si
®
Shortridge Instruments, Inc.
FAST AND ACCURATE MULTIPOINT TEMPERATURES
The AirData MultiTemp is the ideal solution to the problems
encountered in thermal performance testing of air conditioning
systems, cooling towers, heat exchangers, and energy recovery
systems. The MT-440K MultiTemp may be used with any of the
AirData Multimeter and HydroData Multimeter models to measure
temperatures at up to eight separate points in rapid sequence.
Speed is essential to accurate analysis of total heat transfer under
changing load conditions. Temperatures in many systems are
often changing continuously, or the test may be catching the load
“on the fly” at less than full load. After the probes have settled in,
a full set of eight readings requires about 15 seconds. Additional
points may be measured in the same sequence by using more than
one MultiTemp switch unit connected in series (piggybacking).
Reading and memory entry of 64 temperature points would require
about two minutes.
The insertion probes used with the MultiTemp may be used in any
liquid or gas compatible with stainless steel. Typical uses include:
wet or dry bulb air temperatures; thermometer wells; “Pete’s” plugs;
or direct immersion.
7855 East Redfield Road • Scottsdale, Arizona 85260
Phone (480)991-6744 • Fax (480)443-1267 • www.shortridge.com
MULTITEMP KIT AND RELATED PROBES AND ACCESSORIES
MT-440K AirData MultiTemp kit complete with MT-440 eight-position switch unit, six ADT443 insertion probes, $795.00
two ADT444 surface probes, and padded carrying case.
MT-440 MultiTemp switch unit with eight input jacks (for mini-plugs) and one 3’ output cord and plug. $145.00
ADT443 Insertion temperature probe, 1/8” diameter x 4” long, with 12’ cord and mini-plug $125.00
ADT444 Surface temperature probe, 3/16” diameter x 1/8” thick, with 12’ cord and mini-plug $ 95.00
ADT445 Insertion temperature probe, 1/8” diameter x 12” long, with 12’ cord and mini-plug $125.00
XT445 12’ cable extender for ADT443, ADT444, and ADT445 probes $ 30.00
AP446 Adapter plug with 12’ cord to connect ADT442 and ADT446 probes to MultiTemp $ 40.00
PA447 Plug adapter with 3’ cord to “piggyback” one MultiTemp onto another MultiTemp to expand reading $ 25.00
input capacity to 15 or more sensing points.
OPTIONAL PROBES FOR AIRDATA MULTIMETERS THAT MAY BE ADAPTED FOR USE WITH MULTITEMP
ADT442 Insertion temperature probe, 1/8” diameter x 4” long, 3-pin female connector $125.00
ADT446 Insertion temperature probe, 1/16” diameter x 4” long, 3-pin female connector $125.00
TEW19 Temperature extension wand, 19” long $ 50.00
TRC16 Temperature retractile cord, 1’ to 6’ long $ 50.00
PA448 Plug adapter allows mini-plug probes to connect to AirData and HydroData Multimeters $ 25.00
Typical A/C system testing application
Printed in USA July 2009
Some applications include humidity control systems; direct
expansion A/C systems; outside air adjustment; hot water heating;
chilled water; condenser water; and many other circulating process
liquid systems.
The surface probes may be used to measure pipeline surface
temperatures when piping systems do not have thermometer wells.
These probes may also be used as fast acting air probes.
The ADT443, ADT444, and ADT445 TemProbes have mini-plug
connectors for use with the MultiTemp. The ADT442 and ADT446
TemProbes have 3-pin female connectors for use with the AirData
Multimeter and HydroData Multimeter. Pin adapters are available
to allow any of the TemProbes to be used with either the MultiTemp
or the Multimeters.
TEMPERATURE PROBE SPECIFICATIONS
Resolution is 0.1°F.
Operating range of the ADT446 is –20°F to 180°F.
Operating range of all other probes is –67°F to 250°F.
Accuracy is +/- 0.5°F between 32°F and 158°F.
Specifications are subject to change without notice.